Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
Just how do you actually feel with regards to How to Install a Bathtub Yourself?
Installing a tub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging task. If the old tub is readily accessible, the project can move speedily; if you have to open a wall to remove the old tub and also position the brand-new bathtub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Make sure you have actually certified yourself for the work as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This article will certainly aid you install a new tub in your bathroom if you have actually already gotten a new tub as well as don't require to transform the setup of your previous water supply pipelines.
Your devices and product list ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain any water staying in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. As soon as the supply pipelines have been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Using both wooden boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the water supply as well as inspect all joints as well as new pipework for leakages and tighten them if necessary. Fill the tub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub must wait till the tub has actually been used a minimum of once as this will resolve it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers are in place between the faucet and the sink. Secure the faucet in position with the supplier given backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous type ought to be attached to the tap finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, causing problems with wetness and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently available on the market. It is advisable to fit the tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece on Tools You Need to Install a New Bathtub . Thank you so much for taking a few minutes to browse our blog post. Do you know somebody who is serious about the topic? Feel free to share it. We recognize the value of reading our article about How to Install a Bathtub.
Reliable plumber? Dial now! Report this page